How to protect wire from excessive heat?

1

When the weather suddenly skyrockets with temperatures above 85 F. (29 C.), many plants will inevitably suffer from ill effects. However, with adequate care of outdoor plants in extreme heat, the effects of heat stress on plants, including vegetables. can be minimized.

So how do plants cope with heat once temperatures begin to soar? While some plants, like succulents. are well equipped with handling heat by conserving water in their fleshy leaves, the majority of plants do not have this luxury. Therefore, they will normally suffer from the in heat some way or other.

Generally, heat stress of a plant will show itself by wilting, which is a sure sign that water loss has taken place. If this is ignored, the condition will worsen, as the plants will eventually dry up, turning a crunchy brown before dying. In some cases, yellowing of the leaves may occur.

Heat stress of a plant can also be recognized by leaf drop, especially in trees. Many plants will actually shed...

0 0
2
Water heaters and Tankless water heaters are not protected from surge.
Microwave, washing machine, etc are not protected from surge.
microwave, oven
Homeowner insurance might have appliance exclusion. Read homeowner policy
Water heater warranty does not cover surge event.
Protect 120V and 240V circuits with whole house surge protector
Whole house surge will protect all 120Volt and 240Volt household electronics like microwave, dishwasher, oven, water heater, timers etc that have no surge protection. Aso protects breakers and wires.
Install as close to main breaker as possible. Connect to 20 amp duple-pole breaker. Connect to Neutral and ground.

240v appliances not protected from surge/ Oven, HVAC etc.

Water heaters with electronics, microwave, timers etc are not protected from surge

Resource:
Why use surge protection/ pdf?
Buy:
Whole house surge protectors at Amazon

Surge protection will protect:

-Will...
0 0
3

Protecting from Frost

Frost is potentially very damaging. Its arrival may be unexpected, and it often follows or precedes fairly mild weather, when plants are particularly vulnerable. Early-winter frosts, and the late frosts that occur once plants have started growing again in spring, are the most damaging.

Providing Insulation

Protect the root ball of a container plant – and the pot itself – by wrapping the container in burlap, newspaper, or bubblewrap. Tie in place.

Row covers Drape plants with horticultural fleece or film, or old net curtains, to protect flower buds and soft, new growth. Remove as soon as frost is no longer a danger.

For simple and inexpensive overnight frost protection, cover vulnerable plants with a layer or two of newspaper held in place with bricks or large stones.

Protecting Roses

Mound up soil around rose stems during very cold weather. Remove the soil when the weather warms up. If the soil is heavy or...

0 0
4

C. Sherman Johnson Company Incorporated was founded in 1958 by Curtiss S. Johnson Jr (1925 - 2005). Mr. Johnson's love of sailing inspired him to design and manufacture stainless steel turnbuckles, fittings and marine accessories for the pleasure marine market. Many patents and innovative designs lead Johnson Marine (Trade Name) to become one of the largest OEM supplies of life line hardware in the marine industry. Somewhere in the middle 1980's Johnson Marine started to be contacted by architects looking to design railings in buildings using stainless steel aircraft cable with the cable as infill for the railings. At the time this new "cable railing" was thought to be a "fluke" or an anomaly that was a niche design fad. Little did anyone know it was not.

After many calls for cable railings, the light bulb went on and a new division was formed called Johnson Architectural Hardware to design, market and manufacture specific architectural hardware for cable and wire railings....

0 0
5

What is Wire Duct, and what separates it from raceway and other cable management solutions? Typically, it refers to a wire trough that easily allows for organization, pulling and separation of cables. Often it features a sliding cover and "fingers" on the side that create slots for cables to be added, removed or rerouted along the length of the run. The slots feature rounded edges to protect wires and hands from cuts and abrasions. Solid wall units are available to protect sensitive cables and electrical wiring from debris, dust and other outside contaminants. Installation is accomplished via drilling or adhesive mounting.

Wire duct is a type of cable manager that allows you to route large bundles of cabling in an easy and organized fashion. Most options have a sliding or hinged cover that allow you to easily drop in or remove cables and bundles from the run. The bundles that utilize wire duct are usually larger than those used in raceway or many other aesthetic cable...

0 0
6

Video tutorial on how to solder copper wire and apply heat shrink tube. The type of solder that was used was rosin core and the type of wire used in the video is cross link which is quite common in automotive or electronic applications. Rosin paste flux is not not required for this application as we are using rosin core solder instead. Rosin is intended to help the solder flow better while also adhering to the objects you are working with. This method also works with standard strand wire. Electrical tape can be used to provide protection on the soldered joint, but shrink tube is a much better method. Shrink tube will provide a better insulation, looks cleaner, will last longer, and is much more resistant to moisture. Heat shrink normally comes in black, but can also be purchased in specific colors to match the wires you are working with. There is also heat shrink tube available which an internal adhesive which allows for a perfect water tight connection. Be sure to solder in a well...

0 0
7
...
0 0
8
...
0 0
9

1. When applying solder to a splice connection,

the solder is applied directly to the soldering tip.
the solder is applied at the instant that the heat is applied.
the solder is applied to the splice after it has been heated for a few seconds.
both a and b.

2. The most commonly used solder for soldering a component or leads is:

20/80 bar solder.
60/40 resin-core wire solder.
40/40 solid wire solder.
50/50 acid-core wire solder.

3. Technician A says the AWG gauge number for a copper wire is determined by the length of the wire. Technician B says it is determined by the type of insulating material used on the wire. Who is correct?

technician A only.
technician B only.
both Technicians A and B.
neither Technician A nor B.

...
0 0