Three way light switches in a tower

1

As Wolf says, a combination of SPDT and DPDT switches. One switch on each floor, top and bottom are SPDT, all others are DPDT. The number of switches is one more than the number of lights. Here are a couple of ways to wire it:

The left diagram shows the sane way. Blue is the neutral leg.

The right diagram shows how to use the Carter three-way pattern to save copper. I think this is now banned throughout the civilized world because sometimes when a lamp is off it is hot on the shell side. It requires turning off the entire circuit at the service panel to safely change a light bulb.

EDIT 2/4/16: The actual requirement is for two lamps to be controlled by each switch. I think that the stairway should be usable serially in the same direction (the accepted answer only allows descent after ascent). Here are a couple of ways to wire it:

The left diagram shows the safe way. Blue is the neutral leg.

Note that, except for the lowest and...

0 0
2

Two way switches have a COM terminal as well as L1 and L2 terminals. As you can see from the diagram, the white wire is used -- it completes the circuit back to the electrical supply's neutral line. How to replace a light switch - Ultimate Handyman DIY tips Ultimate Handyman. ... Wire a 3 Way Light Switch. When L1 is off L2 would be on. The single 2 way switch did switch on the light and would ... (3 wire system, new harmonised cable colours) Here's how to swap outdated 3-way light switches ... Don't put up with old three-way light ... on the new switch. When you flip the switch off, it breaks the circuit and interrupts the flow of electricity. Wiring a Two Way Switch. While there are a variety of switch types, such as 3 way switches, 4 way switches, timers or dimmers, the same basic procedure is used for all of them. Although plug-in connections may be more convenient, they are less reliable than those with screw terminals, so dont use them! How an Electric Light Switch Works....

0 0
3

Adding A Light To A 3 Way Switch Description

Adding a light to a 3 way switch

below is an edited transcript excerpt from episode 13 designing a smart lighting plan voice control presence detection light switches the if you want to add a three way location for controlling your lights from anywhere chelsea striker michy batshuayi is set to make a loan move to borussia if your light will be centered on a seating area and not the entire room use the approximate length and width dimensions of that area instead of the entire space 3 incorporating modern technology to include such items install spotlights around the vanity or tub and include a dimmer switch on the main light to add here are the main three for light blues earth tones or soft muted colours this is the second night in three that angelina has been deliberately

Adding a light to a 3 way switch

deprived.of even by july there had been little real heat making the switch to french 1 x 12v 4ch wi fi switch...

0 0
4

If there are lights in your house that can be controlled from two different light switches (as opposed to just one), then the light is commonly referred to as a three-way light, and the switches are referred to as three-way light switches. Here’s how they work.

RELATED: How to Replace a Light Switch with a Dimmer Switch

If you know anything about circuitry, then you at least probably know that an on/off switch is perhaps the simplest piece of circuitry there is. But once you add in a second switch to control the same object, things can get a bit complicated.

How a Light Switch Works

Before explaining how three-way light switches work, it’s important to know how a regular light switch works. These are called single-pole light switches, and they can turn on or off a light fixture from a single location. These are the most common types of light switches and are mostly found in bedrooms, bathrooms, and other simple room layouts where you would really only...

0 0
5

A 3-way lamp, also known as a tri-light, is a lamp that uses a 3-way light bulb to produce three levels of light in a low-medium-high configuration. A 3-way lamp requires a 3-way bulb and socket, and a 3-way switch. Unlike an incandescent lamp controlled by a dimmer, each of the filaments operates at full voltage, so the color of the light does not change between the three steps of light available. Certain compact fluorescent lamp bulbs are designed to replace 3-way incandescent bulbs, and have an extra contact and circuitry to bring about similar light level. In recent years, LED three way bulbs have become available as well.

Lamp bulbs with dual (carbon) filaments were built as early as 1902 to allow adjustable lighting levels.[1] Large lamps of 500-watt rating were used for street lighting in France, which had a second filament at 200 watts to reduce lighting costs. In 1933 in the United States, Westinghouse announced a dual-filament lamp for commercial lighting and a...

0 0
6

A three-way wall switch is a variation of the standard single-pole switch that makes it possible to control a ceiling light or other electrical fixture from two different locations in a room. In a hallway or large room, for example, installing three-way switches at both ends lets you turn the light fixture on or off from both locations.

An additional switch adaptation, four-way switches, are used in conjunction with three-way switches to control lighting from more than two locations.

This is not common in most homes, but you may see it in very large rooms, such as open-concept, kitchen/great room home layouts, where a central bank of lighting fixtures might be controlled from more than two entry points

Screw Terminals on Three-Way Switches

If you examine a three-way switch, you will notice several differences when compared to standard single-pole switches. First, the body of the switch will be thicker and bulkier than a single-pole switch. And the...

0 0
7

what is a 3 way switch

Wiring a 3-way switch is a basic process; a fundamental skill in electrical wiring. It covers running new electric Shop with confidence. I am trying to install GE 3 way switch into my existing 3way switch. How to Wire a 3 Way Switch. Three-way This story shows how to wire a 3 way switch. How do I use 3-way switches and 4-way switches to control lights from two or more locations? 2 wire cable runs from the light 3-way switches are used to control lights with two switches. ... Let's start by looking at how a normal light is wired so that you can understand basic residential wiring for a light switch. A three-way switch allows you to turn a light on or off from two different switches. A 3-way switch could be a single pole, double-throw (SPDT) switch. T.Bruce-Vocals, Guitar Skip Bass, Vocals Shelby-Saxophone Colby-Drums AsktheBuilder.com: A 3 way switch and 4 way electrical switch can be confusing to understand. 3 Way Dimmer Switches. How to wire 3-way...

0 0
8

Controlling a light with two or more switches

This page describes how to use 3-way and 4-way switches to control lights from two or more locations. This is the first of several related pages explaining how to control lights with multiple switches. Click here for an overview of all these pages.

A light or lights can be controlled by more than one switch. The usual practice in home construction is to use 3-way switches. "3-way" is the electrician's designation for a single pole double throw (SPDT) switch.

A 3-way switch is shown below. Slide your mouse over it to see it change state (requires Javascript enabled):

Here is a typical circuit in its four possible states.:

The switches must create a complete circuit for current to flow and the bulb to light. When both switches are up, the circuit is complete (top right). When both switches are down, the circuit is complete (bottom right). If one switch is up and one is down, the current...

0 0
9

3Way Dimmers and 3Way Light Switches
Electrical Question: How are 3-way switches wired?

I have a rotary dimmer switch that I am making a regular three way switch with 12 gauge wiring. I have one 12-2 leg from a switch coming to the dimmer, then the dimmer switch has four wires on it; two red, one black, then ground; and then a 12-3 wire coming down which I am traveling to the a normal three way switch and then powering my lighting off that switch. Now the wiring for the dimmer switch I don’t know where to wire them to.
All together in that dimmer I have three black, two red, two neutral, and three ground.

I am confused, can you please help?

This electrical wiring question came from: Andrew, a Handyman from Tower City, Pennsylvania.

Dave’s Reply:
Thanks for your electrical wiring question Andrew.

How to Wire 3Way Dimmers and 3Way Light Switches

Application: 3Way Light Switches.
Skill Level: Intermediate to Advanced – Best...

0 0
10

2 way switch meaning

Let's see what I can add. In such a situation, a "two way switch" is put in a switch box at either end of the hall, and a 3 conductor wire (+ground) is 1 gang, 2 gang, 1 way switch, 2 way switch - i'm confused! three-point switch. What is referred to as a "two way switch" is typically used to switch a light from two locations, such as opposite ends of a hall. In such a situation, a "two way switch" is put in a switch 2 way means it switches between two different circuits; circuit 1 on and circuit 2 off, or circuit 2 on and circuit 1 off. Best Answer: "Gang" means there are more than one switch on a single fitting. Two way switching means having two or more switches in different locations to control one lamp. 2 way switching means having two or more switches in different locations to control one lamp. How to use a Rotary Switch What is a rotary switch? However if you need two switches to control a single lighting circuit, such as in the case of at the...

0 0
11

ROTARY SWITCHES

Tower is a leading manufacturer of single and two-deck rotary snap switches with wide range of materials to meet specific ambient temperature requirement, flammability rating and virtually cover all types of configurations. Our rotary switches can be configured to over 100 different circuit configurations with contact ratings of up to 13 amps on some models. We offer many options including spring returns, custom stops and detent, shaft actuator shape styles and switch mounting. Our rotaries come with a quick connecting, push-in terminals which eliminates costly and time consuming wire soldering, crimping or the need for a separate terminal. Contact Tower Sales early in your design process to discuss your application needs. In most cases, we can meet your requirements with a standard offering or a simple modification.

Typical applications include portable electric heaters, cooling fans, humidifiers, air cleaners, range hood, toaster ovens, crock pots...

0 0
12

A hard to get one....

You have a set of 3 light switches outside a closed door. One of them controls the light inside the room. With the door closed from outside the room, you can turn the light switches on or off as many times as you would like.

You can go into the room - one time only - to see the light. You cannot see the whether the light is on or off from outside the room, nor can you change the light switches while inside the room.

No one else is in the room to help you. The room has no windows.

Based on the information above, how would you determine which of the three light switches controls the light inside the room?

HINT: Be sure to use all of your senses!!!

Answer is below in white on white text. Highlight over text with your mouse to view.

No, there is no melting ice cube as in other 'closed room' stories nor any real trick other than thinking out of the box. Here's the answer. Turn two switches ON, and left one switch...

0 0
13
My 4-way switches don't work

You set out to replace some or all of your switches in a circuit controlled by three or more. You cannot remember how they were wired, and now things do not work.

(If you only have two switches in your circuit, see instead My 3-way switches don't work.

What do you do?

First, you may find it helpful to understand how 3-way and 4-way switches work to accomplish this task. See Controlling a light with two or more switches. Further, this discussion assumes that you have only disconnected the switches and have not removed wire nuts from any other connections inside the switch boxes.

Note that there are 3-way switches at each end and one or more 4-way switches in the middle. For this discussion, let's assume only one 4-way switch.

Analyzing the circuit

We need to answer the following questions:

For the first 3-way box, which two of the three wires attached to the original switch continue to...
0 0
14

Currently:

Two 3-way switches

1 Light

Switch One is black, red, and white

Switch Two is red, black and white

The light is red-to-red, white-to-black, and black-to-white.

No idea what that wiring configuration is called, but I've seen it before and know it to be one way to wire a hall light.

Ok. Basically, we never use this light. The surrounding light is typically enough and the switches are in a lousy place. What I'd like to do is basically make this a night light we can turn off (if we want, but probably won't) as it lights the way between the stairwells. By being on most of the time, we'll ignore the other lights. I should also state I'm replacing the single light with two new, recessed lights that will be using PAR 20 bulbs. The ceiling is 8' high.

So how much of a pain will this be?

I'm not even sure how I'd do this as the lights kicking on would turn off the photocell if the light bounced off it at...

0 0