What power tool is the best and fastest to take up floor tile?

1

With these types of tiles you do not want them to break as they are harder to demo when they are in bits and shards. If you try to use a scraper (even power) what inevitably ends up happening is the top of the tile comes off, leaving the much harder to remove bottom on. Also this method severely damages the subfloor, sometimes to the point that you will have to put a new subfloor in.

What you simply want is a mallet or a hammer. Let me be really clear since I have demo'ed at least 50 of these bathrooms now and I think I have it down to a science.

Start in a corner. Hammer the edge tiles flat. When I say hammer, imagine that you are playing drums in marching band, not hammering a nail. You want some force but not enough to break the tiles (they are usually hard to break when striking straight down). Bring hammer up 8-12 inches with each strike, hitting a small area repetitively. The first couple of rows might take 20-30 taps for a small group of tiles. This method does...
0 0
2

All those answers are good, but layout is critical, make sure you measure off the straightest wall at both ends with the biggest piece you can get to hit, then check the other side of the room on how it will land, vice versa north and south, strike a line once you have it decided and mark a starting point. When laying peel and stick dont push down on the first 5 tiles you lay on your chalk line, in case you go off the line and have to reset. For difficult cuts like doorways, unless you know how to scribe, heat the tile up gently (backside) and lay down, let it lap up and cut real slow with utility knife around the jamb, dont tear tile.
Scribing means after you have laid all your 12 inch tiles, not its time to start cutting in, you lay one tile over top the one on the floor(exactly), take another tile the same size and push up against baseboard, where it lands on tile that is on top of tile on floor, mark with pencil line, cut it and that piece laying on top of the...

0 0
3

Types Of Vacuum Cleaners

It’s important, before anything, that you are aware of the kind of vacuum you want as there are a number of varieties to choose from.

Most noteworthy is that each type comes with both advantages and disadvantages. Due to this, it is good to base your preference on how well the vacuum will suit you. Here are the types of vacuums:

Upright Vacuum

This is the category where all traditional vacuums fall into. In fact they use lint, bags to collect dust, and grime. Especially relevant, is that they have to plug them in and push them around the house when cleaning floors.

However, the types mostly in use today are the ones that use filters and canisters to collect dirt. Besides, you can empty the canisters, wash and re-use; which is more eco-friendly than bagged.

Stick Vacuum

They have great maneuverability and are very light. That is, you can clean large...

0 0
4

The best and the craziest cleaning tools for me! Source: 10 Craziest Cleaning Inventions (crazy cleaning, strange inventions, crazy inventions) - ODDEE

1. Cockroach Swatter Slippers

The most effective way to kill a cockroach without needing to get too close to it.

2. Baby Mop

Make your children work for their keep. After the birth of a child there’s always the temptation to say “Yes, it’s cute, but what can it do?” Until recently the answer was simply “lie there and cry,” but now babies can be put on the payroll, so to speak, almost as soon as they’re born. Just dress your young one in Baby Mops and set him or her down on any hard wood or tile floor that needs cleaning.

3. Ear cleaning device with video camera

Now you will be able to see all the dirt during your personal ear cleaning procedure.

4. USB Vacuum Cleaner

See the dust and bread crumbs accumulated in-between your keyboard keys? To provide a convenient way for doing...

0 0
5

How to choose a manual tile cutter?

Rate / Puntua

Choose a manual tile cutter with the help of Tools4pro.

We want to help you to choose the best manual tile cutter easily and according to your tiling needs.

If you have a tiling project and need to cut tiles, you should choose the perfect manual tile cutter. Whether it is a one-off job, or if you intend to cut frequently, it is better to have all the information you need to be able to choose.

The best advantages of manual tile cutters

To make reforms or specific projects of tiling, manual cutters are ideal. There are even many ceramic placements professionals who prefer to use manual cutters before electric ones for endless advantages.

Easy transport of the manual cutting tool. Very fast tools for repetitive cuts. Small size, compared to electrical ones. Being manual, you do not need electricity. Cleaning and maintenance very easy and fast.

How do cutters work?

Tile cutter...

0 0
6

Regrouting kitchen or bathroom tile is one of those secrets of home remodeling you will be glad you learned.

Far from being a time-intensive, challenging activity, it is actually dead-simple and fast--as long as you have the correct tools and materials.

In limited areas--more on that below--grout removal and replacement can even be easier than cleaning bad grout that is too far gone.

Quick FAQs

What happens with this process?

Existing grout is removed with the aid of power tools and some manual... scraping. New grout is forced into the open seams of the tile with a rubber float. Excess grout that remains on the tile surface (a normal part of grouting) is wiped off with a damp sponge. Then, the resultant haze is wiped clean with special haze cleaner.

How fast does this take?

Here's where the "limited areas" part comes in. After everything is set up, you can expect to remove a 4' x 4' section of 6" tile in about two hours. Grouting...

0 0
7

Grout removal might be necessary for a number of reasons, such as removing old tile for new tile installation, regrouting existing tile or cleaning pieces of grout dropped on top of existing tile. To remove extensive amounts of grout from between tiles, small hand tools such as a hammer and chisel or a grout scraper can be used. For large jobs or faster removal, there are power tools available for purchase. The method chosen depends on personal preference and the availability of tools.

A hammer and chisel work well for grout removal. If a chisel is not readily available, a flathead screwdriver with a thin tip might be substituted. One can simply hold the screwdriver at a 45 degree angle to the grout and hammer it with light pressure. After the initial tap with the hammer, the chisel should be aimed away from the remaining grout so the tile itself is not chipped or cracked.

Another way to remove grout is with a grout scraper. This tool is used to scrape away the grout,...

0 0
8


We had laid Riven slate floor tiles onto a concrete floor/screed or self leveller, (tiles 900x600) back in Sept 2011, the footage covered was 31 square meters. Flexible adhesive and grout used for concrete and under floor heating used. We noticed that some of the tiles sounded hollow when you tapped them/walked on them, but everything seemed fine and we thought nothing of it. At the end of January 2012, we turned on our under floor heating (water). Recently though we have noticed that 5 of the tiles, some half under the kitchen move up and down slightly if walked on or make a slight noise.

The tiler is coming back to rectify the moving tiles, he confessed in a telephone conversation that he dab and daubed the tiles onto the floor, from what I have read on the internet, this is fine for bathroom and kitchen walls, but to do this on a floor and with them being such big tiles, surely this is not correct???? Can someone please advise what tool would be used to bring some...

0 0
9

SYNOPSIS

Tom Dredge demonstrates how to remove grout and regrout your tile to make your bathroom or kitchen tile look like new.

TRANSCRIPT

Today we’re going to talk about the removal of old, tired grout. But before we do that, let’s talk about what it is that we’re getting ourselves into.We’ve got individual tiles placed on a water-resistant backer board with adhesive, but placed in such a way that there’s spaces in between them. That space can vary anywhere from a sixteenth of an inch to a quarter of an inch. As we see here, this is about a quarter of an inch spacing right here. When those tiles dry, those spaces in between need to be filled with a substance. The substance we’re dealing with today is grout. Which is what we’re going to remove today, and put in new.In order to do that, two things we need depending on the size of the job. We have a hand tool with an abrasive blade, that on small areas, work in such a way that scrape away the grouting that’s...

0 0
10

Tile flooring is one of the most popular options in floor coverings today. From the easy to install vinyl tiles to the beautiful options for ceramic tile, there is something for just about every taste. Along with beauty, there are a number of reasons why tile is both practical and popular. It's usually easy to install and maintain, comes in a range of designs, and can be used in nearly any room.

One of the main benefits associated with a tile floor is its ease of maintenance. With both vinyl or ceramic flooring, the tiles require no special cleaning solutions, tend to be stain resistant, and make it much easier to keep clean. Spills can be wiped up easily. Routine cleaning can be accomplished with mild cleansing solution and a sponge mop.

The ease of installation is another advantage associated with tile. Often, the flooring installation involves nothing more than peeling a protective backing from each tile and setting it in place. This makes it possible for...

0 0
11

Why do we differentiate between floor and wall tiles? Surely a tile is a tile? Well, it sort of is – tiles aren’t really manufactured specifically as floor or wall tiles, but instead are made and classified according to their durability and strength. It is this classification that determines where they can be used.

Why is it done this way? Well, tiles may all seem similarly sturdy when you stand on them, but different tiles are suited to different levels of foot traffic. Some can handle heavy footfall – think of how many people must walk over floor tiles in a shopping centre every day – and some can’t really handle any, which is why they can only be fitted on a wall.

So, in effect, every floor tile can also be used as a wall tile – it’s just that the opposite isn’t true. If you’re just tiling your walls, you can essentially choose what you like, but when you’re doing the floor you need to be a bit more careful with your choices.

There are a few different scales...

0 0
12

While cleaning tile floors is still a chore most of us could live without, the evolution of floor care tools has made it easier and more effective than ever. Finding the best vacuum for tile floors, or the best steam mop if that’s your priority is now the challenge. For more on tile and stone flooring cleaning, care and maintenance click here.

The good news is that you’ve got tile floor vacuum and steam mop options to suit your style, and we explore them in this guide to cleaning tile floors and other hard flooring. To jump to our vacuum and steam mop reviews click here.

What is the Best Tile Floor Cleaning Machine for Your Home

This overview of tile floor vacuums and mops will assist you in selecting the best type for your cleaning routine. Below, you’ll find vacuum and steam mop reviews of the top products in each category.

Vacuums for tile floors

Removing loose debris before mopping means you won’t be collecting dirt in your mop –...

0 0
13
...
0 0
14


The sections below discuss the characteristics of various materials, the different types of diamond drill bits, and the special techniques for using diamond drill bits. The most important factors are to use a good diamond drill bit, a slow drill speed (see speed tables below), low drill pressure (see pressure tables below), and plenty of water for lubrication.

Variable speed drills work best since the proper speed can be selected. Some fixed-speed drills have a minimum speed of 600 or 800 rpm, that may be too fast for many diamond drill applications (see speed charts). Impact type "hammer drills" should never be used with diamond drills bits.

Picture shows the thin-wall tip of a Bonded Diamond Bit next to the thick-wall tip of a heavy-duty Pro-Sintered diamond drill bit.

The bonded bits will drill much more quickly but are designed only for drilling...

0 0
15

Ships in 1-7 days.

30-Day Return Guarantee

We want you to be fully satisfied with every item that you purchase from www.acehardware.com. If you are not satisfied with an item that you have purchased (excluding Gift Cards and gas-powered outdoor equipment*), you may return the item up to thirty days after the original purchase date to receive a store credit (less shipping, handling and other charges). We recommend that you make returns of online purchases to an Ace retail store near you which will issue your store credit. If you do not have an Ace retail store near you, please contact a Customer Service Specialist by calling 1-866-290-5334 for complete return instructions. Please refer to our Return Instructions for more information about returning a purchase.

The item must be returned in good condition, in original boxes (whenever possible), and with all paperwork, parts and accessories to insure full credit. After 30 days,...

0 0